Mellanox MHET2X-1SC HCA Card Driver
Mellanox Technologies. s ie og hn ol InfiniHostTM PCI-X Low Profile RoHS HCA Adapter Cards User's Manual Te c P/N: MHET2X-1SC, MHET2X-1TC. Table 5: Firmware Images for InfiniHostTM PCI-X HCA Cards. Table 6: LEDs. Table 7: Jumper Configuration. Table 8: VPD Format for MHET2X-1SC. A2 Adapter Card Firmware ZippyShare extensa forum JHly Low Profile RoHS HCA Adapter Cards User s Manual Te c P/N MHET2X-1SC.
|Supported systems:||Windows 7/8/10, Windows XP 64-bit, Mac OS X 10.X|
|Price:||Free* [*Free Registration Required]|
Mellanox MHET2X-1SC HCA Card Driver
The DUT does not support the technology required to perform this test.
Due to testing station limitations or time limitations, the tests could not be performed. The observed values of the specified parameters are valid at one extreme and invalid at the other. Not tested due to the time constraints of the test period. The IB fabric configuration utilized for any tests requiring Mellanox MHET2X-1SC HCA Card multi-switch configuration is shown below.
- Mellanox Technologies
- Dual Port and related drivers
- OpenFabrics Alliance Interoperability Working Group (OFA-IWG)
- Mellanox Mhet2x-1tc 2-port Pci-x 10gbps InfiniHost HCA Card Adapter
- Ask a Question
- MHET2X-1TC InfiniHost HCA Card, 2-ports 10Gb/s, 128MB, PCI-X
The model name for this device is different than that reported by the HCA. Link status was observed visually via status lights on the device.
Port width and link speed was verified via ibdiagnet. This version of the test plan does not explicitly Mellanox MHET2X-1SC HCA Card a link to be Mellanox MHET2X-1SC HCA Card the proper speed, the next version will. Logo testing in the 2 nd lf of will require proper link speed between all link combinations. Link Partner Device Host: IB Fabric Initialization Test 1: Only one SM is run at a time.
All switches are power cycled between SM trials. All links are validated via use of 'ibdiagnet' and 'ibchecknet' was used to verify that there were no duplicate guids.
Refer to the table below for SM details. An automated test script was used to send ICMP Echo Request packets with payloads of specific sizes between all hosts on the configured fabric.
This procedure was repeated with each subnet manager independently managing the fabric. This procedure was repeated once with each subnet manager independently managing the fabric.
An automated test script was used to transfer a 4MB file using the SFTP protocol between all hosts on the configured fabric. The file was transferred once in each direction between all Mellanox MHET2X-1SC HCA Card, and the contents of the file was verified after each transfer.
The last packet size tested; bytes, was seen to lose the very first packet sent. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, Mellanox MHET2X-1SC HCA Card and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
MHET2X-1TC InfiniHost HCA Card, 2-ports 10Gb/s, 128MB, PCI-X
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
No statement is required for Class B products. If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment Mellanox MHET2X-1SC HCA Card to instruction manual. InfiniBand Copper, current rating: Interface Connectors Pinout B. Figure 7 shows a connector retention clip and the designated names of its secFigure 7: Connector Retention Clip M el tions.
Finally, pull the clip away from its center - see Figure 8 c. The LED Mellanox MHET2X-1SC HCA Card arrangement on the bracket Mellanox MHET2X-1SC HCA Card appearing in this appendix may be different from their arrangement on the actual HCA cards brackets.
OpenFabrics Alliance Interoperability Working Group (OFA-IWG) - PDF
Nevertheless, this difference bears no impact on the replacement instructions provided here. Step 2 - Unscrew bracket screws.
Unscrew both screws from the card using a torque screwdriver as shown in Te c Figure 9. M el la no x Figure 9: Unscrew Bracket Screws Step 3 - Detach bracket. Grip the bracket as shown in Figure 10 placing your thumb on the LED component. In a rotating move toward the component side of the card, slide the bracket out of the connectors Figure Mellanox MHET2X-1SC HCA Card c.